Has anyone built the 3d Printed version of the Mk5 ? how much payload difference would it be with the 3d printed version vs the aluminum version ?
Loading comments…
Has anyone built the 3d Printed version of the Mk5 ? how much payload difference would it be with the 3d printed version vs the aluminum version ?
Loading comments…
A while ago (a long while) I wanted to build the XY mechanism to duplicate the desktop punch press as shown in this article. https://www.cnccookbook.com/a-quick-way-to-make-lots-of-holes-with-cnc/
Well 3D printing has taken over and the need for this or for that matter my 3:1 shear/brake/roller has almost vanished.
The idea of using the AR3/4 hard to hold a piece of sheet metal and move it under the punch and then pause while an operator pulls on the handle is kind of a neat idea. And that the Robot can read G-Code implies simple XY positioning along with the halt or pause.
So suppose two limit switches are set up by the press. One to detect the back edge and one to detect one side. That becomes the HOME location for the XY geometry. After that at hole at X25 Y25 should be easy right?
Is there any sort of app note or discussion on how to do this?
Hello. Can the AR4 push horizontally along the table a 10N force?It's for pushing an ink cartridge into a printer.
The cartridge pushes in via the side of the machine.
Loading comments…
First AR4 integration tests from Ares.
Thanks for sharing!
Good evening,it has been some time I put my AR4 MK3 together and only now start trying to make some actual use of it rather than playing around...
I changed the gripper now to the pneumatic one to have a bit quicker reaction times and stronger grip but ran into some issues when programming it in the HMI. The manual does state to use:
Out On = 8
and
Out Off = 8
to open and close the gripper. This seems not to be working though. Unless I am mistaken, it should be:
Set 5v Output # 8 = 0
and
Set 5v Output # 8 = 1
Tried this and it works well ;) ... 8 is the pin on the Nano as wiring is done the same as in the manual...
On an additional note, I had to remove the diode as it cut out my power supply . It seems to work without just fine without.
Hope this helps someone else too.
All the best,
Frank
Loading comments…
Hello everyone. I am using a stepper motor with an encoder (https://www.oyostepper.com/category-36-b0-Stepper-Motor-w-Encoder.html). To improve noise immunity, I connected the shield of the encoder signal cable to the ground at both the encoder end and the driver end. However, this has caused occasional extra pulse counts during low-speed operation, leading to slight, jittery fluctuations in the coordinates displayed on the CNC screen.
Using an oscilloscope to examine the A/B signals, I observed low-frequency interference—around 50 Hz—superimposed on the waveforms.
According to the technical documentation I've consulted, grounding both ends creates a "ground loop." The potential difference between the two ground points causes a circulating current to flow through the shield, which then couples into the signal lines.
The interference disappeared after I switched to a single-ended ground connection. I would like to ask: should the encoder cable shield be grounded at one end or both ends? And if it should be grounded at only one end, which side is preferable—the encoder side or the driver side?
Thank you.
Hi Chris, Hi everyone
I am currently designing a robot that has bevel gear for j6, the issue is that the bevel gear creates a differential relationship between the joint angles (j5 and j6). When j5 moves, j6 will move also.
Can you please help with a modified code Chris. How difficult it is to modify the Arduino IDE code?
Thanks.
Loading comments…
Hi everyone,
We are evaluating the current AR4 for a broaching machine tending application and would appreciate advice from Chris and anyone with experience using the robot with heavier payloads.
Our workpiece specifications are:
We will also need a gripper, so the total payload at the robot flange will of course be higher than 2.7 kg. We intend to keep the gripper as light as reasonably possible.
Speed is not important for this application. The robot can move slowly and we can use low acceleration. Repeatability, reliability and long-term operation are much more important to us than cycle time.
Before we start modifying the design, we would like to understand what you would recommend for the current AR4 design.
In particular:
We are seriously considering building the robot for this application, and we are also planning to purchase the STEP/SolidWorks CAD files so that we can review and, if necessary, modify the mechanical parts for our use case.
We are able to manufacture or modify mechanical parts if necessary, so we are also interested in any modifications that would make this application more reliable.
Thank you for any guidance or real-world experience.
Loading comments…