Kit guide

Desktop Robot Arm Kit: Build the AR4

The AR4 is a desktop robot arm you build from a kit: machined aluminum, belts and bearings, a Teensy 4.1 controller and closed loop stepper motors. Here is what you buy, what you build and what your bench needs.

AR4 MK5 combo kit with machined aluminum parts, hardware and electronics

Four purchases, one arm

The combo kit ($1,229) is the arm. Motors, drivers and the power supply come from StepperOnline ($699). Covers are printed, and a gripper bolts to the flange.

Kit + motors

$1,928

Axes

6

Payload

1.9 kg

Reach

629 mm

What you buy

AR4 desktop robot arm kit purchases
1. AR4 MK5 combo kit$1,229: aluminum structure, hardware and primary electronics from Annin Robotics
2. Motor package$699: stepper motors, drivers and power supply, factory direct from StepperOnline
3. Printed coversPETG covers and spacers: print your own from the free STL files, or buy a set from C.I. Printing
4. GripperServo gripper parts kit $74.50 or pneumatic gripper parts kit $139, or your own tool

Prefer to spread it out? The combo is also sold as three kits: aluminum ($699), hardware ($319) and electrical ($229). Motors are bought separately on purpose: they ship factory direct with no markup.

What you build, step by step

The free AR4-MK5 build manual is the reference for every step, and the online build course follows it lesson by lesson so you can mark progress.

  1. Step 1Check the bill of materialsChapter 1 lists every part, tool and printed cover. Lay it all out before you start.
  2. Step 2Base enclosure and driversMount the stepper drivers, rocker switch, fan and power wiring in the printed base.
  3. Step 3J1 to J3Install the J1 spindle and platform, the J2 arm and motor, then the J3 joint with its HTD belt.
  4. Step 4J4 to J6 wristFit the J4 turret housing, the J5 and J6 wrist and belts, then wire the J6 cable.
  5. Step 5Harness and baseRoute the harness back through J2, land every wire on the terminal blocks and close the base.
  6. Step 6Firmware, tests and calibrationLoad the Teensy sketch, test every limit switch and encoder, then calibrate (Chapter 8).

What your bench needs

  • A sturdy surface to bolt or clamp the base to. The finished arm weighs 12.25 kg (27 lb).
  • Clear space for the 629 mm (24.75 in) reach envelope around the base.
  • Mains power for the 24 VDC supply (198 W, 8.25 A max).
  • A computer for the HMI: the packaged build runs on Windows, and the Python source runs on Linux and macOS. You also need the Arduino IDE to load the Teensy sketch.
  • Air supply if you choose the pneumatic gripper. Any small compressor with a regulator works, per the manual.

Why a kit instead of an assembled arm

Building the arm is part of the value. You see every bearing, belt and connector, so when something needs attention later you know where to look. Every part is sold separately, and the design files are published, so a worn part is a quick swap instead of a return.

The trade is time. An assembled desktop arm runs the day it arrives; the AR4 takes a build. If you want to compare both routes, see the desktop robot arm buyer's guide.

Kit plus motors

$1,928

Combo kit $1,229 + StepperOnline motor package $699. Grippers and printed covers are extra.

FAQ

What comes in the AR4 desktop robot arm kit?

The combo kit has 26 machined aluminum pieces, all bearings, belts, pulleys, shafts, pins and fasteners, and the primary electrical components, including Hall effect homing on joints 1 to 3 and the HTD belt drive on joint 3.

What is not in the kit?

The stepper motors, drivers and power supply (bought factory direct from StepperOnline), a gripper or tool, and the 3D printed covers and spacers.

Can I buy the AR4 assembled?

Not from Annin Robotics. The AR4 stays a kit to keep the price low, and building it teaches you how the arm is wired and how to troubleshoot it.

How long does it take to build?

Plan on several sessions. The manual walks through the bill of materials, the base and each joint from J1 to J6, the harness, then the startup and calibration procedure.

Do I need a 3D printer?

No. You can print the PETG covers and spacers yourself in any color, or buy a printed set from C.I. Printing.

Can I buy the kit in parts?

Yes. The aluminum, hardware and electrical kits are sold separately, and every part is sold on its own for repairs.