Application guide

Robot Arm for CNC Machine Tending

Load and unload a small CNC machine with the AR4: a 6 axis arm that talks to your PLC over Modbus and can ride a 7th axis track between machines.

AR4 robot arm reaching into a CNC mill to load a part

The tending cell

A tending cell needs three things from the robot: enough reach and payload to move parts, a way to trade signals with the machine controller, and room to grow. The AR4 covers them with its standard arm, the Modbus PLC upgrade and the additional axis outputs.

Reach

629 mm

Payload

1.9 kg

Repeatability

0.25 mm

Extra axes

Up to 3

The Modbus PLC upgrade

The AR4 communicates with PLC devices over Modbus RS-485, which lets it share signals with multiple devices on the same cell.

AR4 Modbus PLC upgrade kit: RS-485 TTL board, wires and RJ45 keystone jack
AR4 Modbus PLC upgrade
Price$16
IncludesRS-485 TTL board, wires and screws, RJ45 keystone jack
ProtocolModbus over RS-485, 2 wire
Baud rate38400
StationSet to any device number you need
MountingInside the J1 base enclosure tray, wired to the Teensy 4.1 breakout

Add a 7th axis travel track

The AR4 can control up to three additional axes. A 7th axis travel track is the most common, and it lets one arm move along a row of machines.

Drivers

One DM332T digital stepper driver per added axis, or a DM320T for a smaller motor, factory direct from StepperOnline.

The track

The manual builds a screw drive track on 500 mm guides. Build it any length, or use a belt drive or your own design.

Other uses

A turntable or part rotation device, camera focus and aperture, or a stepper motor gripper.

Wiring, the auxiliary enclosure and the track build are in Chapter 6 of the build manual. Print files for the auxiliary enclosure are on the downloads page.

Plan the cell

AR4 robot arm mounted on a CNC router table with its control box and keyboard
  • Keep parts and gripper together under the 1.9 kg rated payload.
  • Check that the vise or fixture sits inside the 629 mm reach from the J1 center.
  • Pick a pneumatic or servo gripper; both are wired through the Arduino Nano or Mega.
  • Use Modbus to trade start, done and door signals with the PLC that runs the cell.
  • Guard the cell and follow the safety practices for your shop and machine.

Build a tending cell

$1,928 + $16

AR4-MK5 combo kit with motors, plus the Modbus PLC upgrade. Ordering for a shop or school? Ask for a quote.

FAQ

Can the AR4 talk to a PLC on a CNC cell?

Yes, with the $16 Modbus PLC upgrade. It adds an RS-485 TTL board and an RJ45 keystone jack so the robot communicates over Modbus RS-485. Chapter 3 of the build manual covers wiring and settings.

What Modbus settings does the AR4 use?

RS-485 2 wire at 38400 baud. You can set the station to any device number you need. The manual shows a Direct Logic PLC example.

Can I add a 7th axis travel track?

Yes. The AR4 can control up to three additional axes (7th, 8th and 9th). Chapter 6 of the manual shows a 7th axis travel track built from 500 mm guides with a screw drive, using a DM332T driver per axis. The track can be any length, and belt drive works too.

What else can an additional axis drive?

The manual lists a turntable or part rotation device, camera focus and aperture, and a stepper motor gripper.

What payload can the AR4 handle when tending a machine?

The AR4-MK5 is rated for 1.9 kg (4.15 lb), with 629 mm (24.75 in) reach and 0.25 mm repeatability.

Which gripper should I use?

The pneumatic gripper or the servo gripper. Both are wired through the Arduino Nano or Mega that handles 5 V grippers and I/O.