Application guide
Pick and Place Robot Arm: Your First Robot Cell
Pick and place teaches almost every robot skill at once: tool frames, approach moves, I/O, registers and cycle design. Here is how to build one on the AR4, from a single part to a pallet and vision picking.

What you need
An AR4, a servo or pneumatic gripper on the Nano I/O board, a fixture or tray for parts, and the free HMI. Add a USB webcam for vision picking.
Payload
1.9 kg
Reach
629 mm
Repeatability
0.25 mm
Max linear speed
100 mm/s
Teach a basic pick and place
- Step 1Set the tool frameEnter your gripper's offset so Cartesian moves are about the fingertips, not the flange.
- Step 2Teach the approachJog above the part and save a position. This is where the arm slows down.
- Step 3Teach the pickMove straight down with a linear move to the grip point.
- Step 4Close and liftClose the gripper, wait for it to settle, then move straight up to the approach point.
- Step 5PlaceRepeat approach, linear down, open, linear up at the place position.
- Step 6LoopCall the routine in a loop, or wait on a sensor input before each cycle.
Pallets, stacks and sorting
Position registers turn one taught pick into a whole tray. Teach the first position, then add a register offset per row, column or layer. The same approach stacks parts and sorts them into bins.
Vision guided picking
When parts are not in fixed places, a USB webcam and the HMI's vision tab find them. Teach each part once, and the program moves to each found part with an offset. The vision guided robot arm guide covers setup.
Pick and place in Python or ROS 2
With the AR4 Python API, a cycle is a few linear moves and gripper calls. Teach the positions by jogging, then let the script repeat the cycle. Keep speeds low at first.
AR4 Python API (sketch)
# AR4 Python API: one pick and place cycle.
# Jog to each spot first and record it with robot.get_position()["pose"]
# ([x, y, z, rx, ry, rz] in mm and degrees).
pick = [...] # taught pick pose
place = [...] # taught place pose
def above(pose, mm=80):
x, y, z, rx, ry, rz = pose
return [x, y, z + mm, rx, ry, rz]
for target, grip in ((pick, nano.gripper_close), (place, nano.gripper_open)):
robot.move_linear(*above(target), speed=20) # approach
robot.move_linear(*target, speed=10) # straight down
grip()
time.sleep(0.5)
robot.move_linear(*above(target), speed=20) # straight upIn ROS 2, the driver README's C++ MoveGroupInterface example runs a pick style sequence: open, safe pose, pick pose, close, back to safe. See the ROS 2 MoveIt tutorial.
Realistic limits
Count the gripper against the 1.9 kg rated payload. With 100 mm/s maximum linear speed, the AR4 suits teaching, prototyping and light, low volume tasks rather than high speed lines. Keep people out of the reach envelope while it runs, and fit an E-stop.
Kit plus motors
$1,928
Combo kit $1,229 + StepperOnline motor package $699. Grippers and printed covers are extra.
Keep reading
FAQ
Can the AR4 do pick and place?
Yes. Pick and place is a natural first program on the AR4: teach approach, pick and place positions, open and close a servo or pneumatic gripper, and repeat. Count the gripper and the part together against the 1.9 kg rated payload, and keep work within the 629 mm reach.
How do I pick parts from a grid or pallet?
Use position registers and offsets in the HMI: teach one position, then add a register offset for each row and column, so one short routine fills or empties a whole pallet.
Can the AR4 pick parts that are not in fixed positions?
Yes, with the HMI's vision system: a USB webcam finds taught parts, and the program moves to each part's position with offsets for the pick.
Which gripper should I use for pick and place?
The servo gripper is simple and needs no air; it suits light parts. The pneumatic gripper is stronger and faster but needs a compressor and 24 V for the valve.
Is the AR4 fast enough for production pick and place?
The AR4 is a light duty arm with a 100 mm/s maximum linear speed. It is well suited to teaching, prototyping and light low volume tasks, not high speed production lines.
